ACI PM Interaction Curve

What's new

Every version of ACI PM Interaction Curve, newest first. You are using version 1.2.0, released 12 November 2026.

Version 1.2.0 Current

2 new2 fixes

Added

  • Design standard input: ACI 318-19 (default) or ACI 318-25. ACI 318-25 adds Cl 21.2.2.3: between 0.1f′c·Ag and Pn,bal, φ is limited to a linear interpolation from 0.90 to φcc (not applied when Pn,bal < 0.1f′c·Ag).
  • Report: the standard in the title and inputs; for ACI 318-25, the φ limit and the φ used at each point.

Fixed

  • Curve chart: the phi Pn,max label is no longer hidden behind the chart buttons when the nominal curve is off.
  • Curve chart in Compare: the legend no longer overlaps the axis labels or curves. Sections A and B are listed below the Moment title, the nominal curves at the top left.

Results

  • No changes to existing results. ACI 318-19 is unchanged, and saved models open as ACI 318-19.
  • ACI 318-25: same nominal strengths; φPn and φMn can be lower between 0.1f′c·Ag and Pn,bal.

Version 1.1.0

5 new2 changed2 fixes

Added

  • Rectangular sections: P-M curve at a rotation angle θ (0 to 360°, from Z), entered by hand. Curve direction now has Z, Y and θ. Plots Mθ = Mz cos θ + My sin θ, with the compression block from the section's four corner triangles.
  • Circular sections: Curve direction with Z, Y and θ. The first bar angle used is the entered angle for Z, less 90° for Y and less θ for θ, plus 360° if below zero. The input and the section drawing keep the entered angle.
  • A ? button above θ opens an animation of the section turning by θ, with the fixed Z and Y axes and the section's own z and y axes.
  • Report: a "Rotated section" figure for a θ curve, after the section visualization, in the summary and detailed reports and the PDF.
  • Detailed report for a rotated curve: bar depths along the bending direction, then for each point the compression block, bar forces, and Mz, My and Mθ in kip-in and kip-ft.

Changed

  • Tie and spiral sizes now include every bar size, #3 to #18.
  • The curve chart shows negative moments when a point has one.

Fixed

  • Section drawing: large ties no longer cut across the corner bars, and their hooks no longer lie over a bar.
  • Section drawing: hooks on small circular ties now start on the hoop, with no gap.

Results

  • No changes to existing results. Z and Y are calculated as before, and θ = 0° and 90° give exactly the Z and Y curves. Other angles match the reference calculation (rect_pm) at every point.
  • Circular sections: Z is unchanged; Y and θ use the same calculation with the shifted first bar angle.

Version 1.0.0

First release.

  • P-M interaction curves to ACI 318-19 for rectangular and circular concrete columns, tied or spiral, by strain compatibility with the Whitney stress block.
  • Rectangular sections: a top and a bottom layer, each with its own bar count and size, plus any number of intermediate layers at a chosen depth. Circular sections: bars on a circle, with the angle of the first bar.
  • Seven named points, from pure tension (P1) to the 0.80 or 0.85 P0 compression cap (P7), including the tension controlled limit at εt = εty + 0.003. Moments are taken about the plastic centroid.
  • The curve about the Z or the Y axis of a rectangular section.
  • Compare two sections on one chart, with a table of their capacities side by side.
  • Overlapping bars and layers that do not fit are reported as errors, and no results are shown.
  • Export the curve as CSV, PNG or SVG.
  • A summary or a detailed report, with every calculation step and a drawing of the section, and its PDF.
  • Imperial and metric units.
  • Save and load models as .json files.

Back to ACI PM Interaction Curve