Section Designer

What's new

Every version of Section Designer, newest first. You are using version 1.2.0, released 4 November 2026.

Version 1.2.0 Current

5 new3 fixes

Added

  • Section library: a Standard switch at the top, AISC or AISI. Each standard lists only its own families; AISC has the hot-rolled shapes as before.
  • Section library: AISI cold-formed C-sections from the Cold-Formed Steel Design Manual, as three families: with lips (Table I-1, 85 sizes such as 12CS4x105), with lips for studs and joists (Table I-2, 183 sizes such as 362S162-54), and without lips, the tracks (Table I-3, 237 sizes such as 362T125-54). Each is inserted as one polygon with rounded bends. Its gross properties (A, Ix, Sx, rx, Iy, Sy, ry, x̄ and J) are computed from its dimensions and agree with the published values.
  • Canvas: pointing at a part's corner or centre, a point where parts meet, or the origin shows its x, y coordinates, as do snap points while dragging or drawing. Settings has a "Show coordinates on hover" box to turn this off.
  • Detailed report: a Section parts figure numbers every part, with a table of the parts and whether each is solid or a hole.
  • Detailed report: area, centroid and second moments are worked out step by step from the numbered parts: each part's area and own I from its formula, with the values filled in, then the term-by-term sums for A, Cx and Cy, and the parallel axis sums for Ix, Iy and Ixy. Overlapping solids and holes off the material are cut down to their net area, with the reason given.

Fixed

  • The section library opened on the first family each time. It now opens on the last standard, family and size, with the list scrolled as it was, also after a reload.
  • The Detailed report box was cleared on going to the Section tab and back. It now keeps its setting, also after a reload.
  • The report went back to the top on going to the Section tab and back. It now opens where it was left, unless the section, units, decimal places or detail changed.

Results

  • No changes to calculated results. Part areas in the report use the exact formulas, with π for curved edges; where they differ from the traced outline in the last digit, the report notes it.

Version 1.1.0

5 new2 changed2 fixes

Added

  • Double click a dimension label on the canvas to type a new value for it. Enter or clicking away applies it, Escape cancels.
  • While drawing a polygon, the horizontal and vertical distances from the last vertex to the cursor are dimensioned on the canvas. A distance of zero is not shown.
  • Settings, next to Custom units, sets the most decimal places shown: one setting for the canvas, one for the panels and the report (results, input fields, the section library, the report and its PDF). Both default to 3 and go from 1 to 8. In engineering notation they apply to the leading number. Changes are applied with Done; Cancel or Escape leaves the settings as they were.
  • Section library: AISC S shapes (American Standard beams), S3 to S24, 28 sizes. Each is inserted as a polygon with flanges tapered 2 in 12 and root fillets, which brings A, Ix, Zx and Zy within 2% of the AISC values and Iy within 4%.
  • Section library: AISC double angles, 639 sizes: equal legs, and unequal legs with the long (LLBB) or short (SLBB) legs back to back, each at the gaps AISC lists (0, 3/8 and 3/4 in, and 1-1/2 in for the largest equal legs). Each is inserted as two angles with root fillets; areas, moduli and second moments are within about 4% of the AISC values.

Changed

  • Numbers are shown with the decimal places from Settings instead of a fixed number for each unit and size. Before, mm lengths in the results had 2 decimals and m lengths 5, and in engineering notation the leading number had 3, 2 or 1 decimals depending on its size. Now a value shows its own decimals up to the setting: at 2 places, 6 stays 6, 3.5 stays 3.5 and 22.60111 ×10³ shows as 22.60 ×10³. At the default of 3, an area shown before as 135.6 ×10³ mm² now shows as 135.607 ×10³ mm², and values are no longer padded with zeros.
  • Section library: the shape families are listed down the left side, each with its number of sizes, instead of in a row of tabs, and the family description shows in full. On a narrow screen they are in a dropdown. The dialog is a little wider, so every column of the size table fits.

Fixed

  • Ctrl+C and Ctrl+X did not copy or cut the selected parts after tabbing out of a panel field, because the field still counted as selected text.
  • Pressing Escape, Delete or Ctrl+A in an open dialog also acted on the canvas, for example clearing the selection when Escape closed the dialog.

Results

  • No changes to calculated results. The new decimal places settings change only how numbers are displayed; calculations always use full values.

Version 1.0.0

First release.

  • Build a section from solid and hole parts: rectangles (with optional rounded corners), circles, semicircles, I sections, tees, channels, angles, root fillets and polygons drawn on the canvas.
  • AISC section library: W shapes, C and MC channels, equal and unequal angles, rectangular, square and round HSS, and pipes.
  • Section properties about the centroidal axes: area, centroid, second moments of area, elastic and plastic section moduli, radii of gyration and principal axes.
  • Torsion and warping: torsional constant J, warping constant Cw and shear centre, from a finite element solution.
  • Metric, imperial and custom units.
  • Save and load models as .json files; DXF import and export.
  • Summary and detailed PDF reports.

Back to Section Designer