What is a P-M interaction diagram, and why does it matter in column design?

Real columns almost never carry pure axial load. Frame action, eccentric beams, wind and out-of-plumbness all add a bending moment, and a concrete column's strength in bending depends on how much axial load it carries at the same time. The P-M interaction diagram is the map of every combination it can resist.

PM Curve · 8 min read

One curve instead of two checks

A steel beam can be checked for bending, and a short strut for compression, each on its own. A reinforced concrete column cannot, because axial load and moment act on the same concrete and steel. Compression uses up concrete that would otherwise resist the moment, and below a certain load it actually helps the section resist bending, because it holds back the cracking and yielding on the tension side.

So instead of one capacity, a column has a boundary. Plot axial load P up the vertical axis and moment M along the horizontal one, and every combination the column can carry lies inside a closed curve. Any factored load combination (Pu, Mu) that falls inside the design curve is safe. One that falls outside is not.

0 20 40 60 80 100 120 140 -300 -100 100 300 500 700 Moment, M (kip-ft) Axial load, P (kip), compression up P1 P2 P3 P4 P5 P6 P7 A B C Nominal (Pn, Mn) Design (φPn, φMn) Load point
Nominal and design interaction curves of a 12 × 12 in tied column, 8-#8 bars, f′c = 4 ksi, fy = 60 ksi, from PM Curve. The design curve is the nominal one multiplied by φ and capped at the top. Load points A and B are inside it; C, with the same moment as B but net tension, is outside.

How the curve is built

Each point on the curve is one position of the neutral axis. ACI 318-19 Section 22.2 sets the rules for finding the strength at that position:

Pick a neutral axis depth c, read the strain at every bar, turn strains into stresses and forces, then add them up. The sum of the forces is Pn, and their moment about the plastic centroid (the middle, for a symmetric section) is Mn. Move c from far below the section to above it and the points trace the whole curve.

Section 12 × 12 in, 8-#8 Strain 0.003 εt = 0.00207 Forces Cc = 198 kip a = 4.84 in Cs = 112 kip Ts = 142 kip neutral axis, c = 5.70 in compressiontension
The balanced point of the 12 × 12 in column. The top fibre is at 0.003 and the bottom bars are just at yield, which puts the neutral axis at c = 0.003 × 9.625 / (0.003 + 0.00207) = 5.70 in. The middle bars sit almost at the neutral axis and carry only 7 kip. Compression is drawn to the right of each zero line, tension to the left.

Concrete. a = 0.85 × 5.70 = 4.84 in, Cc = 0.85 × 4 × 4.84 × 12 = 198 kip, acting 3.58 in above the centre.

Steel. Top bars: strain 0.00175, stress 50.7 ksi, force 112 kip after taking off the concrete they displace. Bottom bars: at yield, 60 × 2.37 = 142 kip in tension. Middle bars: 7 kip in tension.

Axial load. Pn = 198 + 112 − 7 − 142 = 160 kip.

Moment. Mn = 198 × 3.58 + (112 + 142) × 3.625 = 1,629 kip-in = 135.8 kip-ft.

The seven key points

PM Curve reports the curve as a full sweep plus seven named points, each tied to a strain condition in the deepest bar (εt, tension positive):

PointConditionPn (kip)Mn (kip-ft)φφPn (kip)φMn (kip-ft)
P1Pure tension, all steel yields−379.200.90−341.30
P2Pure bending, Pn = 00115.00.834095.9
P3Tension-controlled limit, εt = εty + 0.003−49.8107.80.90−44.897.0
P4Balanced, εt = εty = 0.00207160.2135.80.65104.188.2
P5Half yield, εt = 0.5 εty323.7121.80.65210.479.2
P6Decompression, εt = 0514.393.60.65334.360.9
P7Code cap, Pn = 0.80 P0677.851.90.65440.633.7

Above the balanced point the column is compression-controlled: the concrete crushes before the tension steel yields, and each extra kip of axial load costs moment capacity. Below it the tension steel yields first, the section is ductile, and in nominal terms a little compression adds moment capacity: Mn rises from 115.0 kip-ft at pure bending to 135.8 kip-ft at the balanced point.

Why the design curve is a different shape

The design curve is not just the nominal curve scaled down. Two code rules change its shape.

φ depends on the steel strain

ACI 318-19 Table 21.2.2 sets φ = 0.65 for tied columns (0.75 for spirals) when the section is compression-controlled, εt ≤ εty, and φ = 0.90 when it is tension-controlled, εt ≥ εty + 0.003. In between it varies linearly. A brittle compression failure gets the bigger safety margin.

For this column the effect is large. Between pure bending and the balanced point the nominal moment rises by 18%, but φ falls from 0.834 to 0.65, so the design moment falls from 95.9 to 88.2 kip-ft. The largest design moment, 97.0 kip-ft, is at P3, under a small net tension.

The flat top

Pure compression capacity is P0 = 0.85 f′c (Ag − Ast) + fy Ast = 847.3 kip. ACI 318-19 Table 22.4.2.1 limits a tied column to 0.80 P0 (0.85 P0 for spirals) to allow for accidental eccentricity, so the top of the curve is cut flat at φPn,max = 0.65 × 0.80 × 847.3 = 441 kip.

How to check a column with it

Plot every factored load combination as a point (Pu, Mu) and see where it falls. For the 12 × 12 in column:

Load pointPu (kip)Mu (kip-ft)φMn at that loadResult
A, heavy gravity300 compression5566.9 kip-ftinside, OK
B, moderate gravity100 compression8588.8 kip-ftinside, OK
C, wind uplift100 tension8581.5 kip-ftoutside, fails

B and C carry the same 100 kip and the same moment. The only difference is that in C the 100 kip is tension instead of compression, and C fails. This is the main reason the diagram matters: the governing combination is not always the one with the largest load. A combination such as 0.9D + 1.0W, with little gravity load and a large wind moment, can control a column that easily passes 1.2D + 1.6L. Without the curve you would not see it.

Why it matters in column design

What the curve does not cover

This 12 × 12 in column has 4.4% steel, inside the 1% to 8% range. The same method applies to any rectangular or circular, tied or spiral column; only the numbers change.

Try it yourself

Open PM Curve, enter the column size, the bars and the materials, and it draws the nominal and design curves with all seven key points and the φ at each, and gives a step-by-step PDF report of the calculation. Sign in, free, to compare two sections on one chart.

FAQ

Frequently asked questions

What is a P-M interaction diagram?

A P-M interaction diagram is a plot of axial load (P) against bending moment (M) that shows every combination a reinforced concrete column section can carry. Load combinations that plot inside the design curve are safe; points outside it are not.

How is a P-M interaction diagram calculated?

By strain compatibility. For each neutral axis depth, the strain is taken as 0.003 at the extreme compression fibre and linear across the section, concrete is a 0.85 f'c stress block over a = beta1 c, and steel is elastic-plastic. The sum of the forces gives Pn and their moment about the plastic centroid gives Mn. Repeating this for many neutral axis depths traces the curve.

What is the balanced point on a column interaction diagram?

The point where the concrete reaches 0.003 at the same time as the extreme tension steel reaches yield. Above it the column is compression-controlled and phi = 0.65 for tied columns; below it the steel yields first. For a 12 x 12 in tied column with 8-#8 bars it is at Pn = 160 kip, Mn = 135.8 kip-ft.

Why can less compression govern a column design?

Below the balanced point, compression helps a column resist bending, so reducing the compression, or putting the column in net tension, reduces its moment capacity. A wind combination with little gravity load can fail a column that passes the full gravity combination.

Why is the top of the design interaction diagram flat?

ACI 318-19 Table 22.4.2.1 limits the axial strength of a tied column to 0.80 P0 (0.85 P0 for spirals) to allow for accidental eccentricity, so the design curve is cut off at phi Pn,max.

Keep reading

More from the blog

For use by qualified engineers. All results must be checked independently before use in any design. See the Terms of Use.