Section properties · Angle

Angle Section Properties Calculator

Enter the two legs and the thickness of an equal or unequal angle, and get its area, centroid, moments of inertia Ix and Iy, product of inertia, principal axes Iw and Iz with their angle, section and plastic moduli and radii of gyration, with every step of the hand calculation set out below.

Free · Every step shown · Checked against Section Designer and the AISC tables

Dimensions

Section properties

A · Area
–
x̄ · Centroid, from back
–
ȳ · Centroid, from back
–
Ix · Moment of inertia
–
Iy · Moment of inertia
–
Ixy · Product of inertia
–
Iw · Major principal
–
Iz · Minor principal
–
α · Principal axis angle
–
Sx · Elastic modulus
–
Sy · Elastic modulus
–
Zx · Plastic modulus
–
Zy · Plastic modulus
–
rx · Radius of gyration
–
ry · Radius of gyration
–
rz · Least radius of gyration
–
Open in Section Designer

Opens this angle in Section Designer, where you can add root and toe fillets, pick AISC single and double angles from the library, and get the torsion constant J, the warping constant Cw and the shear centre.

Step by step, for your section

The working for the dimensions above, as you would set it out by hand. It updates as you type.

How to calculate the properties of an angle section

  1. Split the angle into two rectangles

    The horizontal leg, b × t, and the rest of the vertical leg above it, t × (d − t), so the corner square is counted once. Measure x from the back of the vertical leg and y from the back of the horizontal leg.

  2. Area and centroid

    A = t (b + d − t)     x̄ = Σ Ai xi / A     ȳ = Σ Ai yi / A

    An angle has no axis of symmetry parallel to its legs, so both coordinates of the centroid are needed. The centroid often lies outside the steel, in the corner between the legs.

  3. Ix, Iy and the product of inertia Ixy

    Ix = Σ ( bi hi³/12 + Ai dy,i² ),   Iy = Σ ( hi bi³/12 + Ai dx,i² ),   Ixy = Σ Ai dx,i dy,i

    A rectangle has no product of inertia about its own centroid, so Ixy comes only from the parallel axis terms. With the legs pointing right and up, one leg sits up and left of the centroid and the other down and right, so Ixy is negative.

  4. Principal axes: Iw, Iz and α

    Iw, Iz = (Ix + Iy)/2 ± √[ ((Ix − Iy)/2)² + Ixy² ]     tan 2α = −2 Ixy / (Ix − Iy)

    Because Ixy is not zero, the x and y axes are not the axes of greatest and least stiffness. Those are the principal axes, turned by α: the major axis w and the minor axis z. An equal leg angle has α = 45°.

  5. Section moduli and radii of gyration

    Sx = Ix / (d − ȳ),   Sy = Iy / (b − x̄),   rz = √(Iz / A)

    The section moduli are taken to the leg tips, the farthest fibres, as in the AISC tables. The plastic moduli are taken about the lines with half the area on each side.

Why the z axis matters

A single angle is weakest about its minor principal axis z, not about x or y. A single angle strut buckles about z, so its slenderness is L / rz, and AISC 360 Section F10 checks angles in bending about their principal axes. That is why the AISC tables list Iz, rz and tan α.

We checked this calculator against all 137 single angles in the AISC tables: A, the centroid, Ix and Iy agree within 2.5%, S and Z within 3.5%, and Iz within 6%. The tables include the small fillets at the root and the toes, which this calculator leaves out; the thinnest small angles differ most.

Worked example: L6×4×½

An unequal angle with a 6 in vertical leg, a 4 in horizontal leg and a 0.5 in thickness, as AISC L6×4×½. x from the back of the vertical leg, y from the back of the horizontal leg.

Partb × hA in²x iny indxdyIx,i in⁴Iy,i in⁴A dx dy
1 Horizontal leg4 × 0.5220.251.013−1.7376.0754.720−3.519
2 Vertical leg0.5 × 5.52.750.253.25−0.7371.26311.3201.550−2.560
Σ4.7517.3956.270−6.079

A = 2 + 2.75 = 4.75 in²

x̄ = (2 × 2 + 2.75 × 0.25) / 4.75 = 0.987 in,   ȳ = (2 × 0.25 + 2.75 × 3.25) / 4.75 = 1.987 in

Ix = 17.395 in⁴,   Iy = 6.270 in⁴,   Ixy = −6.079 in⁴

Iw, Iz = 11.833 ± √(5.563² + 6.079²) = 11.833 ± 8.240, so Iw = 20.072 in⁴ and Iz = 3.593 in⁴

tan 2α = 2 × 6.079 / 11.125 = 1.093, so α = 23.77°;   rz = √(3.593 / 4.75) = 0.870 in

A in²x̄ inȳ inIx in⁴Iy in⁴Sx in³Zx in³Iz in⁴rz in
AISC Table 1-74.750.9811.9817.36.224.317.713.540.864
This calculator4.750.9871.9917.46.274.337.783.590.870

Section Designer gives the same values as the hand calculation: A = 4.75 in², Ix = 17.395 in⁴, Iz = 3.593 in⁴, α = 23.77°. The AISC values are within 1.5%; they include the root and toe fillets. The calculator at the top of this page starts with this angle.

FAQ

Frequently asked questions

How do you calculate the moment of inertia of an angle?

Split it into two rectangles without overlap: one full leg and the rest of the other leg. Find the centroid from both legs' areas and centroids. Then Ix and Iy are the sum of each rectangle's own b h³/12 and its area times the square of its distance from the centroid.

What are Iz and rz for an angle?

Iz is the moment of inertia about the minor principal axis z, the smallest moment of inertia of the section about any axis through its centroid, and rz = √(Iz / A) is the least radius of gyration. A single angle strut buckles about this axis, so rz sets its slenderness.

What is the product of inertia of an angle?

Ixy = Σ A dx dy, the sum of each leg's area times its distances from the centroid in x and in y. It is zero only when the section has an axis of symmetry along x or y. For an angle it is not zero, which is why its principal axes are inclined.

What is tan α for an angle?

α is the angle between the x and y axes and the principal axes. From tan 2α = −2 Ixy / (Ix − Iy). The AISC tables give tan α. For an equal leg angle α = 45°, tan α = 1.

Does it match the AISC tables?

Within 2.5% for A, centroid, Ix and Iy, 3.5% for S and Z, and 6% for Iz, across all 137 AISC single angles. The difference is the small root and toe fillets that rolled angles have. For the exact AISC shapes, insert them from the section library in Section Designer.

Is it the same for an equal leg angle?

Yes, enter the same length for both legs. Then Ix = Iy, x̄ = ȳ, and the principal axes are at 45°: the major axis w runs through the corner of the angle and the minor axis z is at right angles to it.

From the blog

Guides and worked examples

More tools

Any other section

For use by qualified engineers. All results must be checked independently before use in any design. See the Terms of Use.