Section properties · Hollow circle
Hollow Circle Moment of Inertia Calculator
Enter the outside diameter and wall thickness of a round tube or pipe, or make the wall half the diameter for a solid circle, and get its area, moment of inertia, elastic and plastic section moduli, radius of gyration and torsion constant J, with every formula set out below.
Section properties
- A · Area
- –
- I · Moment of inertia
- –
- S · Elastic modulus
- –
- Z · Plastic modulus
- –
- r · Radius of gyration
- –
- J · Torsion constant
- –
- d · Inside diameter
- –
Opens this circle in Section Designer, where you can pick AISC round HSS and pipe sizes from the library, add plates or fins, and get a detailed report.
Step by step, for your section
The working for the dimensions above, as you would set it out by hand. It updates as you type.
How to calculate the moment of inertia of a hollow circle
The outer circle less the hole
A hollow circle is a solid circle of diameter D with a concentric hole of diameter d = D − 2t. Both share the same centre, so their properties simply subtract: no parallel axis terms are needed.
Area and moment of inertia
A = π (D² − d²) / 4 I = π (D⁴ − d⁴) / 64
A circle has the same I about every axis through its centre, so there is no strong or weak axis, and every axis is a principal axis.
Section moduli
S = I / (D/2) = π (D⁴ − d⁴) / (32 D) Z = (D³ − d³) / 6
The shape factor Z/S is 1.70 for a solid circle and falls toward 4/π = 1.27 for a thin tube.
Radius of gyration and torsion
r = √(I/A) = √(D² + d²) / 4 J = 2I = π (D⁴ − d⁴) / 32
For circular sections, and only for them, the torsion constant equals the polar moment of inertia, Ix + Iy = 2I.
Solid circle
A = π D²/4, I = π D⁴/64, S = π D³/32, Z = D³/6, r = D/4
The same formulas with d = 0. In the calculator, set the wall to half the diameter.
Matching the AISC round HSS tables
AISC works out round HSS properties with the design wall thickness tdes = 0.93 tnom for ERW tubes. Enter tdes as the wall and this calculator gives the table values. We checked all 189 round HSS sizes in the AISC tables: every value of A, I, S, Z, r and J agrees with the printed figure within 1%, allowing for its rounding to three digits.
Pipe is listed separately in the AISC Manual. Use the design wall thickness given in its table for each size.
Worked example: HSS6.625×0.280
A round HSS with a 6.625 in outside diameter and a 0.280 in nominal wall. AISC uses the design wall tdes = 0.93 × 0.280 = 0.26 in, so the inside diameter is d = 6.625 − 2 × 0.26 = 6.105 in.
D² = 43.891, d² = 37.271: A = π × (43.891 − 37.271) / 4 = 5.199 in²
D⁴ = 1926.4, d⁴ = 1389.1: I = π × (1926.4 − 1389.1) / 64 = 26.373 in⁴
S = 26.373 / 3.3125 = 7.962 in³; Z = (6.625³ − 6.105³) / 6 = (290.77 − 227.54) / 6 = 10.539 in³
r = √(43.891 + 37.271) / 4 = 2.252 in; J = 2 × 26.373 = 52.745 in⁴
| A in² | I in⁴ | S in³ | Z in³ | r in | J in⁴ | |
|---|---|---|---|---|---|---|
| AISC Table 1-13 | 5.20 | 26.4 | 7.96 | 10.5 | 2.25 | 52.7 |
| This calculator | 5.20 | 26.4 | 7.96 | 10.5 | 2.25 | 52.7 |
Section Designer, with the tube drawn as a circle with a circular hole, gives A = 5.199 in² and I = 26.372 in⁴: it traces each circle with 720 short straight sides, which changes I by less than 0.005%. The calculator at the top of this page starts with this tube.
FAQ
Frequently asked questions
What is the moment of inertia of a hollow circle?
I = π (D⁴ − d⁴) / 64, where D is the outside diameter and d the inside diameter. It is the same about every axis through the centre.
What is the moment of inertia of a solid circle?
I = π D⁴ / 64, or π r⁴ / 4 in terms of the radius. Its section modulus is S = π D³ / 32 and its plastic modulus Z = D³ / 6.
Why is J equal to 2I for a circle?
In a circular shaft the cross-sections stay plane when it twists, so its torsion constant is the polar moment of inertia, Ix + Iy = 2I. For every other shape the sections warp and J is smaller than the polar moment.
What wall thickness should I use for a round HSS?
AISC uses the design wall thickness tdes = 0.93 tnom for ERW tubes made to ASTM A500, and the full nominal wall for ASTM A1085. Enter tdes and the results match the AISC tables.
Is it accurate for thin tubes?
Yes. The formulas are exact for any wall thickness, thick or thin, with no thin-wall approximation.
What is the shape factor of a circular tube?
Z / S: 1.70 for a solid circle, about 1.3 for a typical tube, and 4/π = 1.27 for a very thin one.
From the blog
Guides and worked examples
More tools
Any other section
Section Properties Calculator
Build any cross-section from plates, standard shapes, AISC and AISI steel sections or a DXF outline in Section Designer.
I Beam Moment of Inertia Calculator
Free I beam moment of inertia calculator for symmetric and unsymmetric I sections.
HSS Tube Moment of Inertia Calculator
Free moment of inertia calculator for rectangular and square HSS tubes with rounded corners.
Channel Section Moment of Inertia Calculator
Free channel (C section) moment of inertia calculator.
T Section Moment of Inertia Calculator
Free T section moment of inertia calculator.
Angle Section Properties Calculator
Free angle section properties calculator for equal and unequal leg angles.
Rectangle Moment of Inertia Calculator
Free moment of inertia calculator for a rectangular section.
For use by qualified engineers. All results must be checked independently before use in any design. See the Terms of Use.