Section properties · I beam
I Beam Moment of Inertia Calculator
Enter the depth, flanges and web of any I section, symmetric or not, and get its area, centroid, moments of inertia Ix and Iy, elastic and plastic section moduli and radii of gyration, with every step of the hand calculation set out below.
Section properties
- A · Area
- –
- ȳ · Centroid, from bottom
- –
- Ix · Moment of inertia
- –
- Iy · Moment of inertia
- –
- Sx,top · Elastic modulus, top
- –
- Sx,bot · Elastic modulus, bottom
- –
- Sy · Elastic modulus
- –
- Zx · Plastic modulus
- –
- Zy · Plastic modulus
- –
- rx · Radius of gyration
- –
- ry · Radius of gyration
- –
Opens this I section in Section Designer, where you can add root fillets, cover plates or holes, and get the torsion constant J, the warping constant Cw and the shear centre.
Step by step, for your section
The working for the dimensions above, as you would set it out by hand. It updates as you type.
How to calculate the moment of inertia of an I beam
Split the section into three rectangles
The bottom flange, the web and the top flange. Measure every height from the bottom edge. Each rectangle has its centroid at its own mid-height: y1 = tf,bot/2, y2 = tf,bot + hw/2 and y3 = d − tf,top/2, with the clear web height hw = d − tf,top − tf,bot.
Area and centroid
A = Σ bi hi ȳ = Σ Ai yi / A
The section is symmetric about its vertical centre line, so x̄ is half the widest flange. If the flanges differ, ȳ moves toward the bigger one.
Strong axis, Ix: the parallel axis theorem
Ix = Σ ( bi hi³/12 + Ai di² ), di = yi − ȳ
Each rectangle's own b h³/12, plus its area times the square of its distance from the section's centroid. The flanges are thin, so almost all of their share comes from the A d² term: that is why I beams are efficient.
Weak axis, Iy
Iy = Σ hi bi³/12
Every part is centred on the vertical axis, so there are no A d² terms. The width is now the dimension that is cubed.
Section moduli and radii of gyration
Sx,top = Ix / (d − ȳ), Sx,bot = Ix / ȳ, Sy = Iy / (bf,max/2), r = √(I/A)
The plastic modulus Zx is taken about the plastic neutral axis, the line with half the area on each side, which is not the centroid when the flanges differ: Zx = Σ Ai |yi − yp|, splitting any part the axis cuts.
Shortcut for a doubly symmetric I beam
With equal flanges bf × tf, take the whole bf × d rectangle and subtract the two empty spaces beside the web:
Ix = [ bf d³ − (bf − tw) hw³ ] / 12
Iy = [ 2 tf bf³ + hw tw³ ] / 12
Zx = bf tf (d − tf) + tw hw²/4
Worked example: an unsymmetric built-up I section
A 12 × 1 in bottom flange, a 0.5 × 10 in web and an 8 × 1 in top flange, 12 in deep in all. Heights from the bottom edge.
| Part | b × h | A in² | y in | A y in³ | b h³/12 | d in | A d² | Ix,i in⁴ | h b³/12 |
|---|---|---|---|---|---|---|---|---|---|
| 1 Bottom flange | 12 × 1 | 12 | 0.5 | 6 | 1.000 | −4.62 | 256.133 | 257.133 | 144.000 |
| 2 Web | 0.5 × 10 | 5 | 6 | 30 | 41.667 | 0.88 | 3.872 | 45.539 | 0.104 |
| 3 Top flange | 8 × 1 | 8 | 11.5 | 92 | 0.667 | 6.38 | 325.635 | 326.302 | 42.667 |
| Σ | 25 | 128 | 628.973 | 186.771 |
A = 12 + 5 + 8 = 25 in²
ȳ = 128 / 25 = 5.12 in from the bottom, below mid-height because the bigger flange is at the bottom
Ix = 257.133 + 45.539 + 326.302 = 628.973 in⁴. The two flanges give 93% of it.
Iy = 144 + 0.104 + 42.667 = 186.771 in⁴
Section Designer gives the same values: A = 25 in², ȳ = 5.12 in, Ix = 628.973 in⁴, Iy = 186.771 in⁴. The calculator at the top of this page starts with this section.
FAQ
Frequently asked questions
How do you calculate the moment of inertia of an I beam?
Split it into the two flanges and the web. Find the centroid from the sum of each area times its centroid height, divided by the total area. Then add each rectangle's own b h³/12 and its area times the square of its distance from the centroid (the parallel axis theorem). For the weak axis, add each part's h b³/12.
What is the formula for a symmetric I beam?
Ix = [bf d³ − (bf − tw) hw³] / 12 and Iy = [2 tf bf³ + hw tw³] / 12, where hw = d − 2 tf is the clear height of the web.
Is the moment of inertia the same as the second moment of area?
Yes. In structural engineering, the moment of inertia I of a cross-section means its second moment of area, in units of length to the fourth power (in⁴ or mm⁴). It is not the mass moment of inertia used in dynamics.
Does it include the root fillets of a rolled W shape?
No. This calculator treats the section as three plates, as for a welded plate girder. The fillets of a rolled shape add a little area and stiffness. For W, S and other AISC shapes with their fillets, insert the shape from the section library in Section Designer.
What is the difference between S and Z?
S, the elastic section modulus, is I divided by the distance to the extreme fibre and gives the moment at first yield. Z, the plastic section modulus, is the first moment of the two halves about the plastic neutral axis and gives the fully plastic moment. For I beams Z is about 10 to 15% larger than S about the strong axis.
How do I convert in⁴ to mm⁴?
1 in = 25.4 mm, so 1 in⁴ = 25.4⁴ = 416,231 mm⁴. The calculator does this for you: switch between in and mm at the top.
From the blog
Guides and worked examples
More tools
Any other section
Section Properties Calculator
Build any cross-section from plates, standard shapes, AISC and AISI steel sections or a DXF outline in Section Designer.
HSS Tube Moment of Inertia Calculator
Free moment of inertia calculator for rectangular and square HSS tubes with rounded corners.
Channel Section Moment of Inertia Calculator
Free channel (C section) moment of inertia calculator.
T Section Moment of Inertia Calculator
Free T section moment of inertia calculator.
Angle Section Properties Calculator
Free angle section properties calculator for equal and unequal leg angles.
Rectangle Moment of Inertia Calculator
Free moment of inertia calculator for a rectangular section.
Hollow Circle Moment of Inertia Calculator
Free moment of inertia calculator for hollow and solid circular sections, round HSS and pipe.
For use by qualified engineers. All results must be checked independently before use in any design. See the Terms of Use.