Section properties · Rectangle
Rectangle Moment of Inertia Calculator
Enter the width and height of a solid rectangle, such as a timber joist, a steel plate or a concrete beam, and get its area, moments of inertia Ix and Iy, elastic and plastic section moduli, radii of gyration and torsion constant J, with every formula set out below.
Section properties
- A · Area
- –
- Ix · Moment of inertia
- –
- Iy · Moment of inertia
- –
- Sx · Elastic modulus
- –
- Sy · Elastic modulus
- –
- Zx · Plastic modulus
- –
- Zy · Plastic modulus
- –
- rx · Radius of gyration
- –
- ry · Radius of gyration
- –
- J · Torsion constant
- –
Opens this rectangle in Section Designer, where you can add holes, plates or other shapes, and get the warping constant Cw and a detailed report.
Step by step, for your section
The working for the dimensions above, as you would set it out by hand. It updates as you type.
How to calculate the moment of inertia of a rectangle
Area and centroid
A = b h
A rectangle is symmetric about both centre lines, so its centroid is at its centre, b/2 from a side and h/2 from the bottom.
Moments of inertia
Ix = b h³/12 Iy = h b³/12
The dimension perpendicular to the axis of bending is cubed. That is why a joist is stood on edge: doubling the height multiplies I by eight, doubling the width only by two. About the bottom edge instead of the centroid, I = b h³/3.
Elastic and plastic section moduli
Sx = b h²/6 Zx = b h²/4
S is I divided by the distance to the extreme fibre, h/2. Z is the first moment of the two halves about the centre line, 2 × (b h/2) × (h/4). For a rectangle the shape factor Z/S is exactly 1.5.
Radius of gyration
rx = √(Ix/A) = h/√12 = 0.2887 h
Torsion constant J
J = β a b³, β = 1/3 [ 1 − (192/π⁵)(b/a) Σ tanh(nπa/2b)/n⁵ ], n = 1, 3, 5 …
Here a is the long side and b the short side. This is St Venant's exact solution; the series converges after a few terms. J is not the polar moment Ix + Iy, which is only right for circles: for a square, J is 0.141 a⁴, against a polar moment of 0.167 a⁴.
β for common proportions
| a/b | 1 | 1.5 | 2 | 3 | 4 | 5 | 10 | ∞ |
|---|---|---|---|---|---|---|---|---|
| β | 0.141 | 0.196 | 0.229 | 0.263 | 0.281 | 0.291 | 0.312 | 0.333 |
These are the values of the classic tables (Timoshenko and Goodier, Theory of Elasticity), and the calculator reproduces each of them. For a thin plate, a/b above about 10, J ≈ a b³/3.
Worked example: a 4 × 8 in rectangle
A solid rectangle 4 in wide and 8 in tall, bending about its horizontal centroidal axis x.
A = 4 × 8 = 32 in²
Ix = 4 × 8³ / 12 = 2048 / 12 = 170.667 in⁴; Iy = 8 × 4³ / 12 = 42.667 in⁴, a quarter of Ix
Sx = 4 × 8² / 6 = 42.667 in³; Zx = 4 × 8² / 4 = 64 in³ = 1.5 Sx
rx = 8 / √12 = 2.309 in; ry = 4 / √12 = 1.155 in
a/b = 8/4 = 2, so β = 0.2287 and J = 0.2287 × 8 × 4³ = 117.09 in⁴. The polar moment, 170.667 + 42.667 = 213.3 in⁴, would overstate it by 82%.
Section Designer gives the same A, I, S and Z. The calculator at the top of this page starts with this rectangle.
FAQ
Frequently asked questions
What is the moment of inertia of a rectangle?
About its horizontal centroidal axis, I = b h³ / 12, where b is the width and h the height. About the vertical axis, I = h b³ / 12. About the base, I = b h³ / 3.
Why is the height cubed?
The moment of inertia adds up each strip's area times the square of its distance from the axis. A taller section has more area and that area is farther away, so I grows with h³. Doubling the depth of a beam makes it eight times stiffer.
What is the section modulus of a rectangle?
The elastic section modulus is S = b h² / 6 and the plastic section modulus is Z = b h² / 4, so Z is 1.5 times S.
What is the torsion constant J of a rectangle?
J = β a b³, where a is the long side, b the short side and β depends on a/b: 0.141 for a square, 0.229 for a/b = 2, approaching 1/3 for a thin plate. It is much less than the polar moment of inertia Ix + Iy.
Can I use it for timber or concrete?
Yes. Use the actual dimensions: a nominal 2 × 8 timber joist is 1.5 × 7.25 in. For concrete, it gives the gross section; reinforcement and cracking are not included.
How do I add a hole or another plate?
Open the rectangle in Section Designer, then add more parts or hole parts. The app merges them and works out the properties of the combined section.
From the blog
Guides and worked examples
More tools
Any other section
Section Properties Calculator
Build any cross-section from plates, standard shapes, AISC and AISI steel sections or a DXF outline in Section Designer.
I Beam Moment of Inertia Calculator
Free I beam moment of inertia calculator for symmetric and unsymmetric I sections.
HSS Tube Moment of Inertia Calculator
Free moment of inertia calculator for rectangular and square HSS tubes with rounded corners.
Channel Section Moment of Inertia Calculator
Free channel (C section) moment of inertia calculator.
T Section Moment of Inertia Calculator
Free T section moment of inertia calculator.
Angle Section Properties Calculator
Free angle section properties calculator for equal and unequal leg angles.
Hollow Circle Moment of Inertia Calculator
Free moment of inertia calculator for hollow and solid circular sections, round HSS and pipe.
For use by qualified engineers. All results must be checked independently before use in any design. See the Terms of Use.