Section properties · HSS tube
HSS Tube Moment of Inertia Calculator
Enter the width, height, wall thickness and corner radius of a rectangular or square hollow section, and get its area, moments of inertia Ix and Iy, elastic and plastic section moduli, radii of gyration and torsion constant J, with the rounded corners taken into account.
Section properties
- A · Area
- –
- Ix · Moment of inertia
- –
- Iy · Moment of inertia
- –
- Sx · Elastic modulus
- –
- Sy · Elastic modulus
- –
- Zx · Plastic modulus
- –
- Zy · Plastic modulus
- –
- rx · Radius of gyration
- –
- ry · Radius of gyration
- –
- J · Torsion constant
- –
Opens this tube in Section Designer, where you can add plates or stiffeners, and get the torsion constant J and the warping constant Cw by finite element analysis.
Step by step, for your section
The working for the dimensions above, as you would set it out by hand. It updates as you type.
How to calculate the moment of inertia of a tube with rounded corners
Start from square corners
Take the full B × H rectangle and subtract the b × h hole, with b = B − 2t and h = H − 2t. Then correct for the corners: the outside rounding (radius R) cuts away four small corner pieces, so they are subtracted, and the inside rounding (radius r = R − t) fills four in, so they are added back.
One corner piece of radius ρ
A ρ × ρ square less a quarter circle. Its area, the distance of its centroid from each straight edge, and its second moment about its own centroid (the same about both axes):
a = (1 − π/4) ρ² = 0.2146 ρ²
e = (5/6 − π/4) / (1 − π/4) · ρ = 0.2234 ρ
Ic = (1 − 5π/16) ρ⁴ − a e² = 0.007545 ρ⁴
Area
A = B H − 4 a(R) − b h + 4 a(r)
The tube is symmetric about both centre lines, so the centroid is at its centre.
Ix and Iy: the parallel axis theorem, with signs
Ix = B H³/12 − 4 [ Ic(R) + a(R) (H/2 − eR)² ] − b h³/12 + 4 [ Ic(r) + a(r) (h/2 − er)² ]
Iy is the same with B and H, and b and h, swapped. Each corner piece sits e in from the edges, so its distance from the axis is half the side less e.
Section moduli and torsion
Sx = Ix / (H/2), Zx = B H²/4 − 4 a(R)(H/2 − eR) − b h²/4 + 4 a(r)(h/2 − er)
J = 4 Ap² t / p
Bredt's formula for a closed thin-walled section, on the mid-line of the wall: Ap = (B − t)(H − t) − (4 − π) Rm² is the area it encloses and p = 2(B − t) + 2(H − t) − (8 − 2π) Rm its length, with Rm = R − t/2.
Matching the AISC tables
The AISC Steel Construction Manual works out HSS properties with the design wall thickness tdes = 0.93 tnom and an outside corner radius of 2 tdes. Enter those, and this calculator gives the table values. For HSS6×4×½, tdes = 0.465 in and R = 0.93 in:
| A in² | Ix in⁴ | Zx in³ | Sx in³ | Iy in⁴ | Zy in³ | J in⁴ | |
|---|---|---|---|---|---|---|---|
| AISC Table 1-11 | 7.88 | 34.0 | 14.6 | 11.3 | 17.8 | 11.0 | 40.3 |
| This calculator | 7.88 | 33.9 | 14.6 | 11.3 | 17.7 | 11.0 | 40.3 |
We checked 22 rectangular and square HSS sizes across the AISC tables: every value agrees within 1%. Load HSS6×4×½ into the calculator
Worked example: a 4 × 6 in tube with rounded corners
A rectangular tube 4 in wide and 6 in tall with a 0.5 in wall. The outside corners are rounded to R = 1 in, so the inside corners have r = 0.5 in.
| Corner pieces | ρ in | a in² | e in | Ic in⁴ | 4 a | 4 Ic |
|---|---|---|---|---|---|---|
| Outside | 1 | 0.2146 | 0.2234 | 0.007545 | 0.8584 | 0.0302 |
| Inside | 0.5 | 0.05365 | 0.1117 | 0.000472 | 0.2146 | 0.0019 |
A = 24 − 0.8584 − 15 + 0.2146 = 8.356 in² (square corners: 9.000)
Distances from the x axis: outside pieces 3 − 0.2234 = 2.7766 in, inside pieces 2.5 − 0.1117 = 2.3883 in
Ix = 72 − (0.0302 + 0.8584 × 2.7766²) − 31.25 + (0.0019 + 0.2146 × 2.3883²) = 72 − 6.648 − 31.25 + 1.226 = 35.328 in⁴
Iy = 32 − (0.0302 + 0.8584 × 1.7766²) − 11.25 + (0.0019 + 0.2146 × 1.3883²) = 32 − 2.740 − 11.25 + 0.416 = 18.426 in⁴
Square corners would give Ix = 72 − 31.25 = 40.75 in⁴, 15% too high. Section Designer, with the tube drawn as two rounded rectangles, gives A = 8.356 in², Ix = 35.328 in⁴ and Iy = 18.426 in⁴. The calculator at the top of this page starts with this tube.
FAQ
Frequently asked questions
How do rounded corners change the properties of a tube?
They remove material at the outside corners, farthest from the centroid, and add a little at the inside corners. For a 4 × 6 × 0.5 in tube with R = 1 in, the area drops by 7% and Ix by 13% compared with square corners. Thin walls with small radii change less.
What corner radius should I use for an HSS?
AISC calculates its tables with an outside corner radius of 2 tdes, where tdes = 0.93 tnom is the design wall thickness of an ASTM A500 tube. The inside radius is then R − t. For other products, use the radius from the manufacturer or the standard you design to.
Why does AISC use 0.93 times the nominal wall thickness?
Electric-resistance-welded HSS are made to a tolerance that lets the wall be thinner than nominal, so AISC 360 (Section B4.2) uses 0.93 tnom for ERW tubes to calculate their properties. Use the full nominal thickness for tubes made to a standard with a tighter tolerance, such as ASTM A1085.
How is the torsion constant J calculated?
With Bredt's formula for closed thin-walled sections, J = 4 Ap² t / p, using the area Ap and length p of the wall's mid-line, rounded corners included. It agrees with the AISC tables within 1%. Section Designer also works J out by finite element analysis for any closed or open section.
Does it work for square tubes?
Yes. Enter the same width and height. For a square tube Ix = Iy.
What about round HSS and pipe?
A round tube's I is π (D⁴ − d⁴) / 64. Section Designer has the AISC round HSS and pipe sizes in its section library, and you can draw any circle with a circular hole.
From the blog
Guides and worked examples
More tools
Any other section
Section Properties Calculator
Build any cross-section from plates, standard shapes, AISC and AISI steel sections or a DXF outline in Section Designer.
I Beam Moment of Inertia Calculator
Free I beam moment of inertia calculator for symmetric and unsymmetric I sections.
Channel Section Moment of Inertia Calculator
Free channel (C section) moment of inertia calculator.
T Section Moment of Inertia Calculator
Free T section moment of inertia calculator.
Angle Section Properties Calculator
Free angle section properties calculator for equal and unequal leg angles.
Rectangle Moment of Inertia Calculator
Free moment of inertia calculator for a rectangular section.
Hollow Circle Moment of Inertia Calculator
Free moment of inertia calculator for hollow and solid circular sections, round HSS and pipe.
For use by qualified engineers. All results must be checked independently before use in any design. See the Terms of Use.