Section properties · Channel
Channel Section Moment of Inertia Calculator
Enter the depth, flange width and thicknesses of a channel, and get its area, centroid, moments of inertia Ix and Iy, elastic and plastic section moduli and radii of gyration, with every step of the hand calculation set out below.
Section properties
- A · Area
- –
- x̄ · Centroid, from web back
- –
- Ix · Moment of inertia
- –
- Iy · Moment of inertia
- –
- Sx · Elastic modulus
- –
- Sy · Elastic modulus, toes
- –
- Zx · Plastic modulus
- –
- Zy · Plastic modulus
- –
- rx · Radius of gyration
- –
- ry · Radius of gyration
- –
Opens this channel in Section Designer, where you can add root fillets or lips, pick AISC C and MC channels or AISI cold-formed C-sections from the library, and get the torsion constant J, the warping constant Cw and the shear centre.
Step by step, for your section
The working for the dimensions above, as you would set it out by hand. It updates as you type.
How to calculate the moment of inertia of a channel
Split the channel into three rectangles
The bottom flange, the web and the top flange, each bf × tf or tw × hw, with the clear web height hw = d − 2tf. Measure x from the back of the web and y from the bottom edge, so the flanges cover the web's full height and nothing is counted twice.
Area and centroid
A = 2 bf tf + hw tw x̄ = ( bf² tf + hw tw²/2 ) / A
A channel is symmetric about its horizontal centre line, so ȳ = d/2. It is not symmetric about a vertical line: the centroid sits close to the web, at x̄ from its back face.
Strong axis, Ix
Ix = Σ ( bi hi³/12 + Ai dy,i² ) = [ bf d³ − (bf − tw) hw³ ] / 12
The same as an I beam with equal flanges: the whole bf × d rectangle less the empty space beside the web. Sliding the web to one side does not change Ix.
Weak axis, Iy: the parallel axis theorem
Iy = Σ ( hi bi³/12 + Ai dx,i² ) = 2 tf bf³/3 + hw tw³/3 − A x̄²
About the y axis the parts are no longer centred on the axis, so every part has an A d² term. The short form takes each part about the back of the web, then moves the total to the centroid.
Section moduli and radii of gyration
Sx = Ix / (d/2), Sy = Iy / (bf − x̄), r = √(I/A)
Sy is taken to the flange toes, the fibre farthest from the centroid, as the AISC tables give it. The plastic moduli are taken about the lines with half the area on each side: Zx = bf tf (d − tf) + tw hw²/4, and for Zy that line is usually inside the web.
Rolled AISC channels have sloped flanges
This calculator is for channels with flat flanges: bent plate, built-up and cold-formed channels without lips. AISC C shapes are rolled with a 2 in 12 slope on the inside of the flanges and fillets at the root. Using the average flange thickness gets Ix close, but it puts too much steel at the toes, so Iy, x̄ and the shear centre come out wrong: by 25% for Iy of a C12×20.7. For rolled channels, insert the shape from the AISC library in Section Designer, which draws the real sloped flanges.
Worked example: a 10 × 3 in channel
A channel 10 in deep with 3 × 0.5 in flanges and a 0.375 in web, so the clear web height is hw = 10 − 2 × 0.5 = 9 in. x from the back of the web, y from the bottom edge.
| Part | b × h | A in² | x in | A x in³ | Ix,i in⁴ | h b³/12 | dx in | A dx² | Iy,i in⁴ |
|---|---|---|---|---|---|---|---|---|---|
| 1 Bottom flange | 3 × 0.5 | 1.5 | 1.5 | 2.25 | 33.875 | 1.125 | 0.695 | 0.724 | 1.849 |
| 2 Web | 0.375 × 9 | 3.375 | 0.1875 | 0.633 | 22.781 | 0.040 | −0.618 | 1.288 | 1.327 |
| 3 Top flange | 3 × 0.5 | 1.5 | 1.5 | 2.25 | 33.875 | 1.125 | 0.695 | 0.724 | 1.849 |
| Σ | 6.375 | 5.133 | 90.531 | 5.026 |
A = 1.5 + 3.375 + 1.5 = 6.375 in²
x̄ = 5.133 / 6.375 = 0.805 in from the back of the web; ȳ = 10 / 2 = 5 in
Ix: each flange is 0.031 + 1.5 × 4.75² = 33.875 in⁴, so Ix = 33.875 + 22.781 + 33.875 = 90.531 in⁴. Check: [3 × 10³ − 2.625 × 9³] / 12 = 90.531
Iy = 1.849 + 1.327 + 1.849 = 5.026 in⁴
Sx = 90.531 / 5 = 18.106 in³, Sy = 5.026 / (3 − 0.805) = 2.290 in³, Zx = 3 × 0.5 × 9.5 + 0.375 × 9²/4 = 21.844 in³
Section Designer gives the same values: A = 6.375 in², x̄ = 0.805 in, Ix = 90.531 in⁴, Iy = 5.026 in⁴. The calculator at the top of this page starts with this channel.
FAQ
Frequently asked questions
How do you calculate the moment of inertia of a channel?
Split it into the two flanges and the web. For the strong axis, Ix = [bf d³ − (bf − tw) hw³] / 12, the same as an I beam with equal flanges. For the weak axis, find the centroid x̄ from the back of the web, then add each part's h b³/12 and its area times the square of its distance from x̄.
Where is the centroid of a channel?
On the horizontal centre line, at x̄ = (bf² tf + hw tw²/2) / A from the back of the web. For most channels that is close to the web, well short of the middle of the flanges.
Where is the shear centre of a channel?
Outside the section, behind the web. For a thin-walled channel it is about e = 3 b² tf / (6 b tf + h tw) from the web centre line, with b and h measured between the centre lines of the plates. Loads that do not pass through the shear centre twist the channel. Section Designer works out the shear centre exactly, by finite element analysis.
Does it work for AISC C and MC shapes?
Not exactly. Rolled channels have sloped inside flange faces and root fillets, so their Iy, centroid and shear centre differ from a flat-flange model. Insert the shape from the AISC library in Section Designer to get the real values.
Can I use it for cold-formed C sections?
For a cold-formed channel without lips, with sharp corners, yes. For lipped C sections and studs with rounded bends, Section Designer has the AISI C-sections, studs, joists and tracks in its library.
Why is Sy given to the toes?
Iy is divided by the distance from the centroid to the farthest fibre, which for a channel is the flange toes, at bf − x̄. That gives the smaller of the two section moduli, the one that governs, and it is how the AISC tables list it.
From the blog
Guides and worked examples
Why FE software doesn't match the AISC Cw for a channel
A real rolled C12X20.7 gives Cw = 87 in⁶ against the table's 112 in⁶: why both are right, and which to use.
Elastic vs plastic section modulus: S vs Z
What S and Z mean, how to calculate both, and the shape factors of common sections.
Cold-formed vs hot-rolled channels
Why a cold-formed channel with 14% less steel can have 60% more Ix, and the catch with thin walls.
More tools
Any other section
Section Properties Calculator
Build any cross-section from plates, standard shapes, AISC and AISI steel sections or a DXF outline in Section Designer.
I Beam Moment of Inertia Calculator
Free I beam moment of inertia calculator for symmetric and unsymmetric I sections.
HSS Tube Moment of Inertia Calculator
Free moment of inertia calculator for rectangular and square HSS tubes with rounded corners.
T Section Moment of Inertia Calculator
Free T section moment of inertia calculator.
Angle Section Properties Calculator
Free angle section properties calculator for equal and unequal leg angles.
Rectangle Moment of Inertia Calculator
Free moment of inertia calculator for a rectangular section.
Hollow Circle Moment of Inertia Calculator
Free moment of inertia calculator for hollow and solid circular sections, round HSS and pipe.
For use by qualified engineers. All results must be checked independently before use in any design. See the Terms of Use.