Section properties · T section
T Section Moment of Inertia Calculator
Enter the depth, flange and stem of a T section, and get its centroid, area, moments of inertia Ix and Iy, elastic section moduli at the flange and the stem, plastic moduli and radii of gyration, with every step of the hand calculation set out below.
Section properties
- A · Area
- –
- ȳ · Centroid, from flange top
- –
- Ix · Moment of inertia
- –
- Iy · Moment of inertia
- –
- Sx,top · Elastic modulus, flange
- –
- Sx,stem · Elastic modulus, stem
- –
- Sy · Elastic modulus
- –
- Zx · Plastic modulus
- –
- Zy · Plastic modulus
- –
- rx · Radius of gyration
- –
- ry · Radius of gyration
- –
Opens this T section in Section Designer, where you can add root fillets, a concrete slab or more plates, and get the torsion constant J, the warping constant Cw and the shear centre.
Step by step, for your section
The working for the dimensions above, as you would set it out by hand. It updates as you type.
How to calculate the moment of inertia of a T section
Split the T into two rectangles
The stem, tw × hs with hs = d − tf, and the flange, bf × tf. The stem stops under the flange, so the overlap is not counted twice. Measure heights from the bottom of the stem: its centroid is at hs/2 and the flange's at d − tf/2.
Find the centroid
ȳ = Σ Ai yi / A = [ tw hs²/2 + bf tf (d − tf/2) ] / ( tw hs + bf tf )
A T is symmetric about its stem, so x̄ = bf/2, but not about a horizontal line: the centroid is pulled up toward the flange. The AISC tables give it as the distance from the top of the flange, d − ȳ.
Ix: the parallel axis theorem
Ix = tw hs³/12 + Astem dstem² + bf tf³/12 + Aflange dflange²
Each d is the distance from that part's centroid to the section's centroid. Unlike an I beam, the stem's own b h³/12 is a big share of the total, because the stem is the tall part.
Iy
Iy = tf bf³/12 + hs tw³/12
Both parts are centred on the vertical axis, so there are no A d² terms, and the flange gives nearly all of it.
Two section moduli, and the plastic neutral axis
Sx,top = Ix / (d − ȳ), Sx,stem = Ix / ȳ, Sy = Iy / (bf/2)
The stem tip is far from the centroid, so Sx,stem is much smaller and usually governs. The plastic neutral axis has half the area on each side: when the flange holds more than half the area it lies in the flange, A / (2 bf) below its top, and Zx is the first moment of both halves about it.
WT shapes
AISC WT shapes are cut from W shapes, so they have root fillets where the stem meets the flange. Their tabulated area and stiffness are a little higher than three flat plates would give. To include the fillets, open the section in Section Designer and add fillet parts at the two inside corners.
Worked example: an 8 in deep T section
A 6 × 0.75 in flange on a 0.5 in stem, 8 in deep in all, so the stem is hs = 8 − 0.75 = 7.25 in tall. Heights from the bottom of the stem.
| Part | b × h | A in² | y in | A y in³ | b h³/12 | d in | A d² | Ix,i in⁴ | h b³/12 |
|---|---|---|---|---|---|---|---|---|---|
| 1 Stem | 0.5 × 7.25 | 3.625 | 3.625 | 13.141 | 15.878 | −2.215 | 17.791 | 33.670 | 0.076 |
| 2 Flange | 6 × 0.75 | 4.5 | 7.625 | 34.313 | 0.211 | 1.785 | 14.332 | 14.543 | 13.500 |
| Σ | 8.125 | 47.453 | 48.212 | 13.576 |
A = 3.625 + 4.5 = 8.125 in²
ȳ = 47.453 / 8.125 = 5.840 in from the bottom of the stem, so 2.160 in below the top of the flange
Ix = 33.670 + 14.543 = 48.212 in⁴; Iy = 0.076 + 13.5 = 13.576 in⁴
Sx,top = 48.212 / 2.160 = 22.324 in³, Sx,stem = 48.212 / 5.840 = 8.255 in³
The flange holds 4.5 of the 8.125 in², more than half, so the plastic neutral axis is in the flange, 8.125 / (2 × 6) = 0.677 in below its top: Zx = 14.796 in³
Section Designer gives the same values: A = 8.125 in², ȳ = 5.840 in from the bottom, Ix = 48.212 in⁴, Iy = 13.576 in⁴. The calculator at the top of this page starts with this T section.
FAQ
Frequently asked questions
How do you find the centroid of a T section?
Split it into the flange and the stem, multiply each area by the height of its own centroid, add them up and divide by the total area. Measure from the bottom of the stem, or from the top of the flange as the AISC tables do. The centroid is always closer to the flange than mid-depth.
How do you calculate the moment of inertia of a T section?
Find the centroid first. Then for each part add its own b h³/12 and its area times the square of the distance from its centroid to the section's centroid (the parallel axis theorem). For Iy, both parts are centred on the axis, so Iy is just the sum of each part's h b³/12.
Why does a T section have two section moduli?
Its centroid is not at mid-depth, so the top of the flange and the tip of the stem are at different distances from it. S = I / c gives one value for each. The stem tip is farther away, so its section modulus is smaller and the stem reaches yield first.
Where is the plastic neutral axis of a T section?
On the line with half the area on each side. When the flange holds more than half the area, as in most tees, it lies in the flange, at A / (2 bf) below the top. Otherwise it lies in the stem.
Can I use it for a concrete T beam?
For the gross concrete section, yes: enter the effective flange width and the slab thickness as the flange. Reinforcement and cracking are not included: it gives the properties of the plain concrete shape.
Does it include fillets?
No. The section is two flat plates, as for a welded tee. Rolled WT shapes have root fillets; add fillet parts in Section Designer to include them.
From the blog
Guides and worked examples
More tools
Any other section
Section Properties Calculator
Build any cross-section from plates, standard shapes, AISC and AISI steel sections or a DXF outline in Section Designer.
I Beam Moment of Inertia Calculator
Free I beam moment of inertia calculator for symmetric and unsymmetric I sections.
HSS Tube Moment of Inertia Calculator
Free moment of inertia calculator for rectangular and square HSS tubes with rounded corners.
Channel Section Moment of Inertia Calculator
Free channel (C section) moment of inertia calculator.
Angle Section Properties Calculator
Free angle section properties calculator for equal and unequal leg angles.
Rectangle Moment of Inertia Calculator
Free moment of inertia calculator for a rectangular section.
Hollow Circle Moment of Inertia Calculator
Free moment of inertia calculator for hollow and solid circular sections, round HSS and pipe.
For use by qualified engineers. All results must be checked independently before use in any design. See the Terms of Use.